Frame:
Complete jig-welded tube frame based on Factory Five '33 Hot Rod chassis, but with rear chassis extension for truck bed and functional gate. Includes all mounts ready to accept small block Ford, 4.6L, 5.0L Coyote, and Chevy SB and LS engines.
• Includes full width roll bar
• Uses 3-link or 4-link rear suspension
Body:
Hand laid 3/16” laminate composite body and panels made with vinylester resin.
• Driver and passenger doors with moulded door liners
• Includes secondary body fasteners assembly.
• Adhesive backed foam weatherstrip
• Door edge trim and fasteners
• Includes multi-adjustable door hinges with bronze bushings with fasteners
• Includes tailgate hinge kit, hinge support plates and fasteners
• Stainless steel-lined composite bedsides and tailgate.
Chassis Aluminium Panels:
Includes CNC cut, pre-formed 6061-T6 aluminium panels for cockpit, trunk, and engine bay.
• Pre-packaged rivets; 1/8” short and long, 3/16” short and long
• Complete cockpit aluminium
• 1/8” firewall between engine and passenger compartment
Complete Front Suspension:
Unequal length A-arm control arms with in-board coil-over shock suspension. Comes complete with all parts and fasteners.
• KONI™ brand high-performance nickel-plated, rod-end shock absorbers
• Coil-over kit for KONI™ dampers including spring hat, threaded seat and black powder coated performance springs
• Adjustable lower control arms with ball joints and fasteners
• Upper tubular control arms with ball joints and fasteners
• Grade-8 mounting hardware
Factory Five Rear Suspension:
Our 4-link rear suspension includes rear axle brackets, fasteners and axle straps to mount your Mustang 8.8” rear solid axle and brakes. Comes with all hardware required for installation.
• 4-Link Suspension
• KONI™ brand high-performance nickel-plated, rod-end shock absorbers
• Coil-over kit for KONI™ dampers including spring hat, threaded seat and black powder coated performance springs
• Factory Five tubular upper and rear lower control arms, with polyurethane bushings and fasteners
Complete Front Brake Kit:
• Custom spindles with fasteners
• Front hubs, fasteners and dust covers
• Front brakes, Ford Mustang 11” front rotors with twin piston PBR calipers, brake pads and fasteners
•Master cylinder (listed in pedal box assembly), stainless braided brake line, front and rear with mount clips, banjo bolts and brake line mounting fasteners
• Pre-flared 3/16” brake line and brake line T-adaptor
• OEM Ford Mustang emergency brake handle, fasteners and cable
Complete Steering System:
Complete steering system using rear steer manual rack from tie rod ends and fasteners to steering wheel and badges.
• Manual steering rack with inner and outer tie rod ends and fasteners
• Polyurethane steering rack bushing and fasteners
• Nickel plated lower steering shaft
• 14” banjo steering wheel with boss and ceramic FFR centre section and fasteners
• Steering system, including flange bearings and fasteners
• Custom Ididit tilt steering column with frame mounts
Complete Fuel System/Parts:
This assembly provides everything from the gas cap to the lines, and is designed to work with carburettors or fuel injection systems. External fuel pump required.
• Fuel tank with mounting hardware, vent, gaskets, pick-up and fuel level sending unit
• Fuel filler neck and fasteners
• Pre-flared fuel lines (1/4” and 5/16”) with unions, barbs, hose clamps and high press flex lines and fasteners
• Aircraft style brushed aluminium fuel cap with gaskets, ground strap, fuel hose to tank with fasteners
• 3/8” line fuel filter, connectors and hose clamps
Complete Cooling System/Parts:
Electric cooling fan and mounting hardware, radiator hoses, and all necessary fasteners.
• Electric cooling fan and mounting kit with connectors
• Aluminium radiator with cap and filler neck
• Stainless steel radiator hose kit includes adaptor kit, fasteners and hose
• Overflow tank with cap, hoses, hose clamps and mounting hardware
• 185-degree thermostat switch and wiring
Engine Accessories:
The ‘35 Hot Rod Truck kit is configured to accommodate the engine of your choice.
• Engine/transmission mounts (select 302/351, 4.6L, 5.0L Coyote, SB and LS Chevy), with fasteners
• Exhaust, with gaskets and fasteners
Driveshaft:
Select from one of seven available driveshafts with fasteners to match the engine/trans of your choice.
• 28 spline driveshaft for T-5, AOD, or Tremec 3550s
• 31 spline driveshaft for Tremec TKO 500 or 600s
• 31 spline driveshaft for 4.6L or 5.0L Coyote engines with T-45s or 3650s
• 31 spline for LS engine with TKO transmission
• 31 spine for SB Chevy with TKO transmission
Gauges, Dash, and Electrical Assembly:
Complete assembly comes with dash buttons, and indicator lights, switches, and horn.
• Custom fit chassis wiring harness
• Ignition switch and FFR key, headlight switch, hi-low beam switch, starter solenoid and horn button
• Dash indicators: green, blue dash lights (LED)
• Wiring harness mounting kit and hardware including fuse panel mount
• Insulated line clip hardware and fasteners and cable ties
• Battery ground strap
• Speedometer sending unit, pigtail, fasteners and speedometer gear
• A complete set of six Autometer
Platinum electronic gauges, with connectors, terminals and installation kit
Includes the following gauges:
• Speedometer
• Tachometer
• Oil Pressure Gauge
• Water Temperature Gauge
• Fuel Level Gauge
• Voltmeter
Complete Interior Accessories:
The ‘35 Hot Rod Truck kit comes with all the interior accessories you need and want. Bucket seats, door latches, rear view mirrors, and more complement the dash and gauges assembly for a full interior.
Check out this full list of standard parts and assemblies:
• Metal framed bucket seats, black vinyl with fasteners
• 5-point Simpson brand harnesses;
• 3” wide driver and passenger, frame mounted with fasteners
• Complete cockpit carpet set, black all-weather
• Emergency brake boot, black leather
• Interior rear view mirror with fasteners
• 6-gauge electronic Autometer Platinum gauges (see description above in gauge assembly)
• Interior door latches and fasteners
• Leather shifter boot and fasteners
• Pleated door panels
• Stitched arm rest
• Banjo style steering wheel (listed in steering assembly), with polished aluminium boss and centre badge
Exterior Accessories and Lighting:
Along with the goodies on the inside of the car, the ‘35 Hot Rod Truck kit is loaded with the right exterior parts and trim on the outside.
• DOT safety glass windshield
• License plate light and bracket with fasteners
• Headlamp assemblies, including chrome buckets, halogen headlamps, with integral (LED) turn signal, and fasteners
• Red rear LED tail lights
• Lighting is DOT approved
Complete Pedal Box and Components:
The ‘35 Hot Rod Truck kit utilises the proven Wilwood brand pedal box with fasteners and all the required ancillary parts.
• Wilwood pedal box and mounting hardware
• Master cylinders
• Accelerator pedal, accelerator cable, return spring and ball stud retainer, with fasteners
• Brake line adaptors and T-fittings
Assembly Manual:
Bound assembly manual that is full of pictures, diagrams, and CAD drawings.
Fasteners:
More than 1,600 top quality zinc plated, chrome and stainless steel USS, metric and SAE fasteners, numbered and packed individually by assembly.
What needs to be added to the complete kit is:
- Engine and gearbox, we got you covered with engine packages direct from Blue Print engines.
- Rear end and rear brakes.
- Wheels and tires again we have packages available if you wish to stay period
- Paint
- Battery
